Categories

KKmulticopter V5.5 controller blackboard Quadcopter + USB Programmer + Signal Distribution Board

KKmulticopter V5.5 controller blackboard Quadcopter + USB Programmer + Signal Distribution Board
KKmulticopter V5.5 controller blackboard Quadcopter + USB Programmer + Signal Distribution Board
Product Code: TD-KKB5.5
Availability: Out Of Stock
Price: Rs. 1,799.00
Qty:     - OR -   Add to Wish List
Add to Compare

 

KK multicopter V5.5 controller Board

Description:

The KKmulticopter is a KK flight controller board for remote control multicopters with 2,3,4 and 6 rotors. We get KKmulticopter to stablise the aircraft during flight. KK flight controller takes the signal from the three gyros on the board (roll, pitch and yaw) and feeds the information into the Integrated Circuit (Atmega IC). KK flight controller then processes the information according the the KK software and sends out control signal to the Electronic Speed Controllers (ESCs) which are plugged onto the board and also connected to the motors. Depending the signal from the IC the ESCs will either speed up or slow down the motors (and tilt the rear rotor with a servo in a Tricopter) in order establish level flight.
The board of KKmulticopter also takes a control signal from the Remote Control Receiver (RX) and feeds this into the IC via the aileron, elevator, throttle and rudder pins on the board. After processing this information, the IC will then send out a signal to the motors (Via the to M6 pins on the board) to speed up or slow down to achieve controlled flight (up, down, backwards, forwards, left, right, yaw) on the command from the RC Pilot sent via his Transmitter (TX). In the case of a Tricopter, one of the pin connectors (M4) will control a servo achieve yaw authority.

Specifications:

  • Simple structure, KKmulticopter is easy to Maintain and Debug Control.
  • Gyros, relying on potentiometer adjust gyro sensitivity.
  • Full servo signal output, support normal ESC / analog servo.
  • Support for single-axis / UFO, Y3 3-axis, Y4-type 3-axis, 4 axis, 6 axis, V22 flight mode.
  • Supports 4-axis "+" and "X" flight mode, support for six-axis "HEXA6" and "Y6" flight mode.
  • Don't need MK 4-axis PPM decoder board, the receiver can be connected directly to the Transmitter.

Package included:

  • 1 x 4-axis Circuit Board
  • 1 x USB programmer
  • 1 x Signal Distribution Board
  • Female ends connector wire

*image shown is original.

Write a review

Your Name:


Your Review: Note: HTML is not translated!

Rating: Bad           Good

Enter the code in the box below:



Description

 

KK multicopter V5.5 controller Board

Description:

The KKmulticopter is a KK flight controller board for remote control multicopters with 2,3,4 and 6 rotors. We get KKmulticopter to stablise the aircraft during flight. KK flight controller takes the signal from the three gyros on the board (roll, pitch and yaw) and feeds the information into the Integrated Circuit (Atmega IC). KK flight controller then processes the information according the the KK software and sends out control signal to the Electronic Speed Controllers (ESCs) which are plugged onto the board and also connected to the motors. Depending the signal from the IC the ESCs will either speed up or slow down the motors (and tilt the rear rotor with a servo in a Tricopter) in order establish level flight.
The board of KKmulticopter also takes a control signal from the Remote Control Receiver (RX) and feeds this into the IC via the aileron, elevator, throttle and rudder pins on the board. After processing this information, the IC will then send out a signal to the motors (Via the to M6 pins on the board) to speed up or slow down to achieve controlled flight (up, down, backwards, forwards, left, right, yaw) on the command from the RC Pilot sent via his Transmitter (TX). In the case of a Tricopter, one of the pin connectors (M4) will control a servo achieve yaw authority.

Specifications:

  • Simple structure, KKmulticopter is easy to Maintain and Debug Control.
  • Gyros, relying on potentiometer adjust gyro sensitivity.
  • Full servo signal output, support normal ESC / analog servo.
  • Support for single-axis / UFO, Y3 3-axis, Y4-type 3-axis, 4 axis, 6 axis, V22 flight mode.
  • Supports 4-axis "+" and "X" flight mode, support for six-axis "HEXA6" and "Y6" flight mode.
  • Don't need MK 4-axis PPM decoder board, the receiver can be connected directly to the Transmitter.

Package included:

  • 1 x 4-axis Circuit Board
  • 1 x USB programmer
  • 1 x Signal Distribution Board
  • Female ends connector wire

*image shown is original.

Write a review

Your Name:


Your Review: Note: HTML is not translated!

Rating: Bad           Good

Enter the code in the box below:



Copyright © 2014-2018 TechDelivers.com. All Rights Reserved.